Tamper and Vandal Proof Station

Tamper and Vandal Proof Station

Item Number: 1007061000

With scream, assault and tamper alarms.

  • Analogue intercom station specially designed for prison and correctional facilities
  • Advanced safety solution including scream, assault and tamper alarms
  • Vandal proof design with 2.5 mm steel front, sensor button, microphone/speaker protection and water resistant
  • Integrated light signaling system
  • Programmable I/O ports for controlling door status, lamps, TV sets, sensors and more
  • Redundant backup for power and signaling

The analogue Tamper and Vandal Proof Station type 1007061 000 is designed specially for prisons and correctional facilities with safety and security for both guards and prisoners in mind. The station is much more than a traditional intercom for prison cells. The station comes with inbuilt scream alarm, assault alarm, light signaling and external controls. The front plate is in 2,5 mm stainless steel and equipped with one vandal proof sensor call button. If the prisoner in some way should manage to open the station, a tamper alarm will be triggered. If the station is disconnected, or the wires to the station are shorted, a request for action will be generated.

Call request from the cell, guard presence and alarm calls are indicated on the guard’s intercom station as well as by signal lamps outside the cell and in the guard room. The station works in a dual redundant mode. If the link to the intercom exchange fails, the lamp signaling will still work. If the lamp signaling fails, all intercom signaling will remain intact.The sensitivity of the vandal proof sensor buttons can be set to ‘normal’ or ‘high’, where the latter is intended for use by guards wearing rubber gloves.

In order to keep the sensitivity at the correct level, the stations must be installed in a dry, indoor location. For cleaning purposes, the station is protected to IP65; fluid will not harm the station, but operation is only optimal when the surface is dry again.

See also: additional documentation on wiki.zenitel.com
 

General
Dimensions WxHxD 128 x 264 x 51 mm, 5.0 x 10.4 x 2.4 in
Weight 950 g / 2.1 lb
Finish 2.5 mm brushed stainless steel
Mounting Flush in back box, 6 tamper proof screws
Button Vandal proof sensor type
Gen. purp. I/O ports 3 x input - contact closure, 2 x output - 24 VDC/1 A
Lamp outputs Call- present - tamper - group
Lamp drivers 24 VDC/1 A overload protected
Operating Voltage 24 (11-27) V DC
Cable Requirements 2 pair twisted cable, 0.5-0.6 mmØ / 24 AWG
Temperature -40ºC to +55ºC
Relative humidity 0% - 95%
Loudspeaker Output 1 W RMS
Frequency Range 200 - 10 000 Hz
Connector Type Pugable screw terminals
Back-box type LBB 7073/76
ORDER NUMBER DESCRIPTION SHIP WEIGHT
1007061000 Tamper and Vandal Proof Station, one Button 0.95 kg
1007060155 Flush Mount Back Box with Anchors
1007060130 Corridor Lamp
1007060120 Remote Call Button

Date Name Category Size Document
18.09.2019 1007061000 Tamper Vandal Proof Station CAD 2D 90.31 KB Login to download
17.09.2019 1007060155_Flush_Mount_Backbox_with_Anchors.zip CAD 2D 143.64 KB Login to download
17.09.2019 1007060150_On_Wall_Backbox.zip CAD 2D 66.4 KB Login to download
22.07.2019 Declaration of Conformity 1007061000 Tamper and Vandal Proof Station Declaration 138.03 KB Download
8.11.2017 Declaration of Conformity FCC 1007061000 Tamper and Vandal Proof Station.pdf Declaration 32.73 KB Download