ENA2060-DC1

ENA2060-DC1 Network Amplifier

Item Number: 1023122061

Exigo Network Amplifier 2 Channels, 60W for Rolling Stock

  • Less APIs
  • Less Complexity
  • Common Network Infrastructure
  • Freedom of Choice
  • Fan-less design
  • Dual Ethernet Ports

 

https://youtu.be/2NIU64wTf8c?si=h_IyTjIesSLiHPmp
See our Rolling Stock page.
SIP
EXIGO_40x40 Exigo

The ENA2060-DC1 Network Amplifier for Rolling Stock incorporates SIP-addressable loudspeaker loops that enable the use of the same software for handling both Passenger Emergency Intercom / Crew Communication and Public Address (PA), as well as the required Train Radio Integration, thus eliminating one entire subsystem from the solution. This results in a well-integrated system with less complexity and more functionality, while the use of open standards offers freedom of choice when it comes to future upgrades and supply.

  • Two SIP addressable audio channels – 2x60W
  • Supports wide set of IP and networking standards
  • Easily integrated into existing information concepts
  • 100V speaker line technology – ease of cabling with galvanic separation
  • UIC Code 558/568 Compatibility
  • Supports direct audio routing to wide range of induction loop amplifiers
  • Designed, manufactured and tested according to EN50155
  • Designed, manufactured and tested according to EN45545
  • Speaker loop monitoring
  • Local audio inputs
  • Additional I/Os for various integration options
  • Fanless design
  • Built to last with robust extruded aluminum frame
  • Easy to install and commission with minimum maintenance overhead

A modern on-board system normally features an IPBX with SIP capability for emergency call points and their radio integration. The IPBX can be based on proprietary or an open source software architecture that runs on EN50155 approved hardware. Given the usual requirement for on-board PA, the IPBX can easily handle the function of being the PA controller. A complete PA System can thus be provided just through the use of an EN50155 approved SIP amplifier. Eliminating one entire proprietary subsystem not only reduces the total system cost, but also time spent in integration work. Moreover, a clean and robust integration means enhanced passenger safety.

The ENA2060-DC1 Network Amplifier is intended to cover one carriage consisting of two or more PA zones. Examples of such zones can be the left and right side of the carriage, upper and lower deck, or even outside speakers. Redundancy can be achieved by using two amplifiers which ensure that at least 50% of the loudspeakers will still work in case of a failure in one IP PA amplifier (A-B amplifier setup). Hence, public address announcements will still be audible with only a minor drop in sound pressure level.

https://youtu.be/2NIU64wTf8c?si=h_IyTjIesSLiHPmp
Or see our Rolling Stock page.

 

Mechanical
Dimensions (HxWxD) 84 x 213 x 315 mm
Mounting Flange mounting - 6 pcs M5 bolts
Weight 5.3 kg
Enviromental
Operating temperature -40C +70C, EN50155 Class T2 + T3
Operating humidty Yearly average <75% RH; during 30 consecutive days 95%
Air pressure 70kPa - 106 kPa, according to EN300 019
Ingress protection IP-42
Electrical Power
Connector M12 A male
Power supply interruptions EN50155 Class S2
Power supply change over EN50155 Class C1 and C2
Standby power consumption < 15W
Max power consumption < 170W
Audio 100V output
Connector M12 A female
Audio output power Class-D, 60W per channel, 2 channels
Frequency response Hardware: 200Hz - 19kHz
Audio codec G.722 (200Hz - 7kHz)
THD < 0.4%
SNR 70 dB
Protection Self protecting during overload or shorts with temporary shutdown according to EN50121-3-2
Monitoring Line impedance measurements @21kHz
Detects: Short circuit between phases and ground faults
Control: Digitally controlled
Multiconnector
Connector Circular 24pos connector, TE 1-796387
Contains signals desribed below
Audio 0dBV line output
Audio channel Parallel output of each 100V channels
Gain -40 dB +2dB
Impedance 600 Ohm
Levels 0 dBV (1Vrms)
Frequency response Hardware: 200 Hz - 19kHz
Audio codec G.722 (200Hz - 7kHz)
Audio inputs
Microphone input: Electret microphone suitable for 2V bias
Input impedance 1 kOhm
Frequency response Hardware: 200 - 19kHz
Audio codec G.722 (200Hz - 7kHz)
THD 0.4 %
SNR 70dB
Network and protocols
Connector M12 D female x 2
Ethernet 2 x 10BASE-T, 100BASE-X, Auto negotiation, Audio MDIX
LAN protocols IPv4 (with DiffServ), TCP, UDP, HTTPS, TFTP, RTP, DHCP, SNMP, STENTOFON CCoIP® , NTP
SIP RFC 32612 (SIP base standard), RFC 3515 (SIP refer), RFC 2976 (SIP Info)
DTMF RFC 2833, RFC 2976 (SIP Info)
Management HTTP/HTTPS (web configuration)
SNMPv1, SNMPv2c
General inputs and outputs
2 x GPI Configurable
2 x 24Vdc Control outputs 200 mA per output
Short circuit protection according to EN50121-3-2
UIC
Designed according to UIC code 568
UIC Audio input 2 Vrms
200 Hz - 19 kHz bandwidth
Input impedance 10kOhm
UIC priority, UIC on/off Current loop 24Vdc/10mA
Galvanically isolated
Indicators
Power indicator Green LED
Fault indicator Yellow LED
Status indicator Green LED
Audio indicators - one per channel Blue LED
Certifications
EN50155 – S2 Railway applications – Electronic equipment used on rolling stock – Voltage variations
EN50155 – T2 + T3 Railway applications – Electronic equipment used on rolling stock – Temperature requirements
EN50155 – C1 + C2 Railway applications – Electronic equipment used on rolling stock – Supply changeover
EN50121-3 Railway Applications – Electromagnetic compatibility Part 3-1: Rolling stock – Train and complete vehicle
IEC/EN 61373 Category 1, Class B Railway applications – Rolling stock equipment – Shock and vibration tests
EN45545 Railway applications. Fire protection on railway vehicles
EN/AS 60849 Requirements related to speech intelligibility
ROHS 2011/65/EU (ROHS) + 1907/2006EU (REACH)
Operational
MTBF 161000 hous
MTTR 10 minutes
Line Input
Input levels 1 Vrms
Input impedance 10 kOhm
Frequency response Hardware: 200 - 19kHz
Audio codec G.722 (200Hz - 7kHz)
THD 0.4%
SNR 70 dB

Date Name Category Size Document
1.11.2022 RoHS Declaration 2021 Declaration 3.24 MB Download
18.06.2021 ENA2060-DC1-1023122061-CE-03 Declaration 178.18 KB Download
13.10.2020 1023122061 ENA2060-DC1 CAD 2D 288.11 KB Login to download
13.10.2020 A100K11689 Exigo ENA2060-DC1 Manual Manual 1.41 MB Download